![]() It support most-used features and commands of FTP (including many modern extensions), and To use less resources than older servers, be smaller and very secure, and to never execute SYNOPSIS pure-ftpd ] ] ] ĭESCRIPTION Pure-FTPd is a small, simple server for the old and hairy File Transfer Protocol, designed Pure-ftpd - simple File Transfer Protocol server Use 'ALL' to allow access from any IP: vsftpd : ALL : allowĪdd a local user with disabled shell and the home dir set: useradd user_name -shell /sbin/nologin -home-dir /path_to_directoryĪdd the same user to the vsftpd's user list: echo "user_name" | tee -a /etc/vsftpd.Provided by: pure-ftpd-common_1.0.36-3.2build1_all To allow access to vsftpd from the specific IPs, edit /etc/hosts.allow: /etc/hosts.allow ![]() # This option is the name of the file loaded when the userlist_enable option is active.Įnable the vsftpd service and start it: chkconfig vsftpd on When login is denied, the denial is issued before the user is asked for a password. If you set this setting to NO, then users will be denied login unless they are explicitly listed in the file specified by userlist_file. # This option is examined if userlist_enable is activated. # If enabled, vsftpd will load a list of usernames, from the filename given by userlist_file. will be shown in directory listings even if the "a" flag was not used by the client. # If activated, files and directories starting with. # The value that the umask for file creation is set to for local users. # If set to YES, local users will be (by default) placed in a chroot() jail in their home directory after login. These commands are: STOR, DELE, RNFR, RNTO, MKD, RMD, APPE and SITE. # This controls whether any FTP commands which change the filesystem are allowed or not. This must be enable for any non-anonymous login to work, including virtual users. If enabled, normal user accounts in /etc/passwd (or wherever your PAM config references) may be used to log in. # Controls whether local logins are permitted or not. If enabled, both the usernames ftp and anonymous are recognised as anonymous logins. # Controls whether anonymous logins are permitted or not. We recommend you make the following changes: /etc/vsftpd/nf Install vsftpd from the standard CentOS repo: yum install vsftpd -yĪfter installation, you need to edit /etc/vsftpd/nf according to your need. A OUTPUT -p tcp -sport 1024: -dport 1024: -m state -state ESTABLISHED,RELATED -j ACCEPTĪpply changes: iptables-restore /etc/sysconfig/iptables A INPUT -p tcp -sport 1024: -dport 1024: -m state -state ESTABLISHED -j ACCEPT A OUTPUT -p tcp -dport 20 -m state -state ESTABLISHED -j ACCEPT A INPUT -p tcp -sport 20 -m state -state ESTABLISHED,RELATED -j ACCEPT A OUTPUT -p tcp -dport 21 -m state -state NEW,ESTABLISHED -j ACCEPT A INPUT -p tcp -sport 21 -m state -state ESTABLISHED -j ACCEPT Set them to 'on' by executing: /etc/sysconfig/selinuxĮdit iptables config (/etc/sysconfig/iptables) to open FTP-specific TCP ports: /etc/sysconfig/iptables If the values are 'off': allow_ftpd_full_access -> off To elevate privileges use: sudo su -Ĭheck values of the SELinux policy booleans related to FTP: getsebool -a | egrep 'ftp_home_dir|passive|ftpd_full_access' This tutorial will guide you through the process of setting up vsftpd to allow a user to upload files to his or her home directory using FTP.Īll commands in this guide are to be performed by a user with root privileges. How to setup vsftpd FTP server on CentOS 6
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |